XBB PP-CAN-FD®
XBB Dongle® and XBB PowerUnit® in one single unit, for permanent mounting in the vehicle. It wires into the CAN bus of the car rather than the diagnostic socket, which calls for knowledge of vehicle electrics.
Read moreXBB PP-CAN-FD® in short
XBB PP-CAN-FD® is a programmable CAN and CAN FD gateway for permanent mounting in the vehicle. From the outside it resembles an XBB PowerUnit®, but it has the functions of XBB Dongle® built into the same unit.
Two units become one
An installation with XBB PP-CAN-FD® needs no separate XBB Dongle®. The unit reads the vehicle as well as switching the load itself, which turns the installation into one unit instead of two while freeing up the diagnostic socket.
How it works
The unit is wired straight to the CAN bus of the vehicle, interprets the signals according to the recipe you choose and switches its outputs accordingly. The most common use is auxiliary lights and accessories, where a load is to follow a function in the car such as high beam or ignition.
How it differs from XBB Dongle®
XBB Dongle® sits in the diagnostic socket. XBB PP-CAN-FD® is wired into the electrical system and the CAN bus of the vehicle instead, which calls for knowledge of vehicle electrics. In return it suits anyone who cannot, or does not want to, have anything fitted in the diagnostic socket. Some car models also require XBB PP-CAN-FD® rather than XBB Dongle®.
Two outputs plus an analogue input
The unit has two outputs of 10 amps each. If a load needs more current, both outputs can be wired to the same load to share it. The current on each output is shown continuously in the XBB Configurator app, so you can check the installation after mounting. Pin 4 also carries an analogue input, for example to switch the outputs on by hand.
Controls further XBB units wirelessly
If the two outputs are not enough, XBB PP-CAN-FD® works as a master for other XBB products, which it reaches over an encrypted 2.4 GHz radio link. Up to four modules can be connected at the same time, for example XBB PowerUnit 6® or XBB Smart Button®.
Mounting and fusing
The unit is shaped like a relay and mounts in a standard seven pin relay socket to DIN 72552. The socket has to be mechanically secured. The supply to pin 2 must be protected by a blade type automotive fuse of at most 25 amps, sized for the cable that is run. The unit may be mounted in the engine bay, in a protected spot away from heat sources. That is possible because the electronics are fully potted and withstand harsher environments than an ordinary XBB PowerUnit®. There is also a purpose made wiring harness for the unit.
Recipes for your car
Ready made recipes for XBB PP-CAN-FD® are found under compatible car models, in the PP-CAN section. Recipes are loaded through the XBB Configurator app, which is available for both Android and iOS.
Write your own recipes with XBB Code
With XBB Code you write, compile and share your own recipes straight in the browser. You log in with the same account as in the app and can start from a template or from a ready made recipe for your car model.
Technical data
| Operating voltage | 9 to 36 volts |
|---|---|
| Vehicle electrical system | 12 volts, negative ground |
| Temperature range | -30 to +80 °C |
| Standby current | 3 to 5.4 milliamps |
| Housing | Fully potted PA66 plastic |
| Weight | 40 grams |
The unit handles both CAN and CAN FD and is type approved to UN ECE R10. It keeps its settings through a power cut, so the whole system reconnects within a few seconds.
The data sheet has the full details. It is on the page Declaration of Conformity together with the user manual, safety information and the information required by REACH Article 33, in sixteen languages.
XBB and compatible car models
Thinking about using XBB products? Have a look through our compatible car models to see whether we have a recipe that fits your car.
Want to know more, or do you have a question? Have a look in our FAQ to see whether it is already answered there.







